65 lines
3 KiB
JSON
65 lines
3 KiB
JSON
|
{
|
||
|
|
"manufacturer": "Everspring",
|
||
|
|
"manufacturerId": "0x0060",
|
||
|
|
"label": "EH403",
|
||
|
|
"description": "Z-Wave Floodlight with Motion Detector",
|
||
|
|
"devices": [
|
||
|
|
{
|
||
|
|
"productType": "0x0012",
|
||
|
|
"productId": "0x0001",
|
||
|
|
"zwaveAllianceId": 2890
|
||
|
|
}
|
||
|
|
],
|
||
|
|
"firmwareVersion": {
|
||
|
|
"min": "0.0",
|
||
|
|
"max": "255.255"
|
||
|
|
},
|
||
|
|
"paramInformation": [
|
||
|
|
{
|
||
|
|
"#": "1",
|
||
|
|
"label": "PIR Trigger Off Period",
|
||
|
|
"description": "Pir trigger off period can be set 8~720 secs",
|
||
|
|
"valueSize": 2,
|
||
|
|
"minValue": 8,
|
||
|
|
"maxValue": 720,
|
||
|
|
"defaultValue": 15
|
||
|
|
},
|
||
|
|
{
|
||
|
|
"#": "2",
|
||
|
|
"label": "Lux Sensor Threshold",
|
||
|
|
"description": "Lux sensor threshold can be set 30~200",
|
||
|
|
"valueSize": 2,
|
||
|
|
"minValue": 30,
|
||
|
|
"maxValue": 200,
|
||
|
|
"defaultValue": 50,
|
||
|
|
"writeOnly": true
|
||
|
|
},
|
||
|
|
{
|
||
|
|
"#": "3",
|
||
|
|
"label": "Lux Auto Report",
|
||
|
|
"description": "Lux auto report can be set 0~1440 minutes",
|
||
|
|
"valueSize": 2,
|
||
|
|
"unit": "minutes",
|
||
|
|
"minValue": 0,
|
||
|
|
"maxValue": 1440,
|
||
|
|
"defaultValue": 0
|
||
|
|
}
|
||
|
|
],
|
||
|
|
"metadata": {
|
||
|
|
"inclusion": "Auto Inclusion\nThe unit supports Auto Inclusion feature where it will automatically enter Inclusion mode when first powered up after a factory reset.\n\n1. Prepare the Z-Wave controller.\n2. Plug the cable plug to the wall socket to power up the unit.\n3. The Link LED will start to blink slowly with 2-second on, 2-second off (for 2 minutes) which shows the unit does not be paired.\n4. Within 30 seconds, put the Z-Wave Controller into inclusion mode.\n5. The Inclusion process should be completed when the Link LED stops blinking.\n\nNote: If you are connecting this unit to a Z-Wave Controller that utilizes the S2 security protocol, you may be asked by your controller to enter a 5-digit Device Specific Key (DSK) that is unique to each unit. This can be found in one of two places:\n- on the QR code label on the back of the unit\n- on the insert card inside the packaging.\n\n6. Turn on the floodlight using the controller to check if the auto inclusion is working properly.\n\nManual Inclusion\n1. Prepare the Z-Wave controller.\n2. Press the tamper switch 3 times within 1.5 seconds to put the unit into inclusion mode",
|
||
|
|
"exclusion": "1. Put the Z-Wave Controller into exclusion mode.\n2. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode",
|
||
|
|
"reset": "1. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode\n2. Within 1 second of step 1, press the tamper switch again and hold until LED is off (about 5 seconds).\n3. Node ID is excluded. The device reverts to factory default state and will be in auto-inclusion mode for 4 minutes.\n4. Please use this procedure only when the network primary controller is missing or otherwise inoperable",
|
||
|
|
"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2890/EH403%20Manual_20180522修改-A501112670R.pdf"
|
||
|
|
},
|
||
|
|
"compat": {
|
||
|
|
"commandClasses": {
|
||
|
|
"remove": {
|
||
|
|
// The device does not support Supervision correctly
|
||
|
|
"Supervision": {
|
||
|
|
"endpoints": "*"
|
||
|
|
}
|
||
|
|
}
|
||
|
|
}
|
||
|
|
}
|
||
|
|
}
|