127 lines
3.5 KiB
JSON
127 lines
3.5 KiB
JSON
{
|
||
"manufacturer": "SE Devices",
|
||
"manufacturerId": "0x024f",
|
||
"label": "AD1-10V",
|
||
"description": "Standalone 1-10V Dimmer",
|
||
"devices": [
|
||
{
|
||
"productType": "0x0003",
|
||
"productId": "0x1011",
|
||
"zwaveAllianceId": 2857
|
||
}
|
||
],
|
||
"firmwareVersion": {
|
||
"min": "0.0",
|
||
"max": "255.255"
|
||
},
|
||
"paramInformation": [
|
||
{
|
||
"#": "1",
|
||
"label": "Hardware Combination Identifier",
|
||
"valueSize": 1,
|
||
"defaultValue": 18,
|
||
"readOnly": true,
|
||
"allowManualEntry": false,
|
||
"options": [
|
||
{
|
||
"label": "2-Pole 8A relay",
|
||
"value": 16
|
||
},
|
||
{
|
||
"label": "1-10V dimmer",
|
||
"value": 17
|
||
},
|
||
{
|
||
"label": "230V MOSFET dimmer",
|
||
"value": 18
|
||
},
|
||
{
|
||
"label": "1-Pole 16A relay",
|
||
"value": 19
|
||
}
|
||
]
|
||
},
|
||
{
|
||
"#": "10",
|
||
"label": "Dimming Speed",
|
||
"valueSize": 2,
|
||
"unit": "0.01 seconds",
|
||
"minValue": 0,
|
||
"maxValue": 32767,
|
||
"defaultValue": 300
|
||
},
|
||
{
|
||
"#": "11",
|
||
"label": "Dimmer Mode",
|
||
"valueSize": 1,
|
||
"defaultValue": 0,
|
||
"allowManualEntry": false,
|
||
"options": [
|
||
{
|
||
"label": "Leading edge",
|
||
"value": 0
|
||
},
|
||
{
|
||
"label": "Tailing edge",
|
||
"value": 1
|
||
}
|
||
]
|
||
},
|
||
{
|
||
"#": "12",
|
||
"label": "Maximum Dimmer Level",
|
||
"valueSize": 1,
|
||
"minValue": 1,
|
||
"maxValue": 99,
|
||
"defaultValue": 90
|
||
},
|
||
{
|
||
"#": "13",
|
||
"label": "Minimum Dimmer Level",
|
||
"valueSize": 1,
|
||
"minValue": 1,
|
||
"maxValue": 99,
|
||
"defaultValue": 15
|
||
},
|
||
{
|
||
"#": "16",
|
||
"label": "Back Unit Type",
|
||
"valueSize": 1,
|
||
"defaultValue": 2,
|
||
"readOnly": true,
|
||
"allowManualEntry": false,
|
||
"options": [
|
||
{
|
||
"label": "2-Pole 8A relay",
|
||
"value": 0
|
||
},
|
||
{
|
||
"label": "230V MOSFET dimmer",
|
||
"value": 2
|
||
},
|
||
{
|
||
"label": "1-10V dimmer",
|
||
"value": 4
|
||
},
|
||
{
|
||
"label": "1-Pole 16A relay",
|
||
"value": 6
|
||
}
|
||
]
|
||
},
|
||
{
|
||
"#": "44",
|
||
"label": "Cold Start Minimum Level",
|
||
"valueSize": 1,
|
||
"minValue": 1,
|
||
"maxValue": 99,
|
||
"defaultValue": 20
|
||
}
|
||
],
|
||
"metadata": {
|
||
"inclusion": "To add the device to a Z-Wave network, the Z-Wave Controller must first be set into Add (Learn) mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
|
||
"exclusion": "To remove the device from a Z-Wave network, the Z-Wave Controller must first be set into Remove mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
|
||
"reset": "WARNING! Executing a Factory Reset on a device may make it stop working as wanted, and will disable remote control of the device. The device will have to be re-added to the Z-Wave network and reconfigured afterwards, to regain the previous operation of the device. Please DO NOT execute this procedure unless it is absolutely necessary.\n\nPush and Hold the Add/Remove button for about 15 seconds – until the LED indicator turns OFF. Then release the button. The device is now Factory Reset, and removed from the Z-Wave network.\n\nThe button is located about 10 mm down in the middle of the three holes on the front. A thin tool (a very small screwdriver, a toothpick, a paper clip or similar) is needed to access the button",
|
||
"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2857/AMD_AD1-10V%20-%20Standalone%20Z-Wave%20Dimmer%20-%20User%20Manual.pdf"
|
||
}
|
||
}
|