23 lines
3.1 KiB
JSON
23 lines
3.1 KiB
JSON
{
|
|
"manufacturer": "Leak Intelligence, LLC",
|
|
"manufacturerId": "0x0173",
|
|
"label": "LGZWL",
|
|
"description": "Leak Gopher Z-Wave Leak Detector",
|
|
"devices": [
|
|
{
|
|
"productType": "0x4c47",
|
|
"productId": "0x4c44",
|
|
"zwaveAllianceId": 2389
|
|
}
|
|
],
|
|
"firmwareVersion": {
|
|
"min": "0.0",
|
|
"max": "255.255"
|
|
},
|
|
"metadata": {
|
|
"inclusion": "Z-Wave Inclusion \nHow to Add the Leak Gopher Leak Detector to your Z-Wave Controller \n- Plug the wall cube power adapter (included) into the receptacle on the bottom of the Leak Gopher Z-Wave Valve Control marked “5 VDC”. Plug the wall cube into a 110 VAC outlet. \nThis provides power to the Leak Gopher Z-Wave Leak Detector. \n- Configure the Z-Wave Controller to Include/Add a device. \n- When the Z-Wave Controller is ready to include/add a device, it will display a message like “waiting to add device”. Press and release the Z-Wave button on the front of the LGZWLD. \n- The Z-Wave Controller will acknowledge that the LGZWLD has been added to the Z-Wave network. \n- Your Leak Gopher Z-Wave Leak Detector is ready to use.\nInclusion without Security\nIf your home automation hub is does not support the Z-Wave Security Command class, tap the Z-Wave button two times. Tapping the button twice will send a simpler message to the hub which will not include the security command classes.\nInclusion Legacy Mode\nIf your home automation hub does not support the Z-Wave Notification Command Class, the LGZWLD can substitute the simpler Binary Switch command class. To enable Legacy Mode, tap the Z-Wave button three times during inclusion. Virtually all hubs support the Binary Switch command class.",
|
|
"exclusion": "Z-Wave Exclusion \nHow to Remove the Leak Gopher Z-Wave Leak Detector from your Z-Wave Controller \n- Plug the wall cube power adapter (included) into the receptacle on the bottom of the Leak Gopher Z-Wave Valve Control marked “5 VDC”. Plug the wall cube into a 110 VAC outlet. \nThis provides power to the Leak Gopher Z-Wave Valve Control. \n- Configure the Z-Wave Controller to Exclude a device. \n- When the Z-Wave Controller is ready to exclude a device, it will display a message like \n“waiting to exclude device”. Press and release the Z-Wave button on the LGZWLD \n- The Z-Wave Controller will acknowledge that the LGZWLD has been excluded from the Z-Wave network. \n- Your Leak Gopher Z-Wave Leak Detector is excluded from this controller.",
|
|
"reset": "Reset to Factory Defaults \nHow to reset the Leak Gopher Z-Wave Leak Detector \n- If the exclusion process above is not working or the Z-Wave controller was lost or not available, the following process can be used to factory reset the device to the same state it has when shipped new. \n- To reset the Leak Gopher Z-Wave Leak Detector Z-Wave radio and routing tables, press and HOLD the Z-Wave button for 15 seconds. The LED will blink very quickly while holding the Z-Wave button down. Once the LED turns off, release the Z-Wave button.",
|
|
"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2389/LDZW_LeakDetector_Z-Wave_InstructionManual.pdf"
|
|
}
|
|
}
|