60 lines
3.3 KiB
JSON
60 lines
3.3 KiB
JSON
{
|
||
"manufacturer": "Yale",
|
||
"manufacturerId": "0x0129",
|
||
"label": "SR-BX-ZW",
|
||
"description": "External Siren",
|
||
"devices": [
|
||
{
|
||
"productType": "0x6f01",
|
||
"productId": "0x0001",
|
||
"zwaveAllianceId": 2039
|
||
}
|
||
],
|
||
"firmwareVersion": {
|
||
"min": "0.0",
|
||
"max": "255.255"
|
||
},
|
||
"paramInformation": [
|
||
{
|
||
"#": "1",
|
||
"label": "Alarm Duration",
|
||
"valueSize": 1,
|
||
"unit": "minutes",
|
||
"minValue": 1,
|
||
"maxValue": 10,
|
||
"defaultValue": 10
|
||
},
|
||
{
|
||
"#": "2",
|
||
"$import": "~/templates/master_template.json#base_enable_disable",
|
||
"label": "Alarm LED Flash"
|
||
},
|
||
{
|
||
"#": "3",
|
||
"label": "Flashing LED Interval",
|
||
"description": "Control's the siren's LED flash during non-alarm mode. Note: Setting this parameter will significantly reduce the battery life of your siren.",
|
||
"valueSize": 1,
|
||
"unit": "10 seconds",
|
||
"minValue": 0,
|
||
"maxValue": 25,
|
||
"defaultValue": 0,
|
||
"options": [
|
||
{
|
||
"label": "Disable",
|
||
"value": 0
|
||
}
|
||
]
|
||
},
|
||
{
|
||
"#": "4",
|
||
"$import": "~/templates/master_template.json#base_enable_disable",
|
||
"label": "Tamper Alarm"
|
||
}
|
||
],
|
||
"metadata": {
|
||
"inclusion": "ADDING THE SIREN\nThis product can be added and operate in any compatible Z-Wave network. All non-battery operated nodes within the network will act as repeaters, regardless of vendor, to increase reliability of the network.\nAdding steps:\n• Turn on the battery power switch to activate\nthe pre-inserted batteries.\n• The Siren will emit a 2-tone beep.\n• Put the Z-Wave controller into adding or\nLearning mode (please refer to the Z-Wave\ncontroller manual).\n• Within 1.5 seconds, press the Siren learn button\n3 times.\n• Refer to the operation manual of the Z-Wave\ncontroller to complete the learn-in process.\n• If the Siren has already been added (learnt) into\nanother Z-Wave controller, or if the Siren is unable\nto be learnt into the current Z-Wave controller,\nplease remove it first (see Removing the siren below)\nbefore attempting to add it into the current\nZ-Wave controller",
|
||
"exclusion": "REMOVING THE SIREN\nThe Siren must be removed from any existing Z-Wave network before being added into a new Z-Wave network. There are two methods available to remove a device.\nRemoving Mode\n• Put the existing Z-Wave controller into Removing Mode (please refer to the Z-Wave controller manual).\n• Within 1.5 seconds, press the learn button 3 times and the Siren will be removed from the existing Z-Wave network.\n• The Siren is now ready to be added to a new Z-Wave controller",
|
||
"reset": "Factory Reset (Only use this when the existing Z-Wave controller is missing or inoperable).\n• Turn off battery power switch and disconnect 9V power adaptor (if present).\n• Press and hold the learn button.\n• While holding the learn button, power on the Siren (power switch ON and reconnect the 9V power adaptor). Keep holding for 10 seconds to complete the factory reset.\n• Please note that the existing Z-Wave controller will still retain the Siren’s Z-Wave setting. Please refer to the Z-Wave controller manual on remove procedures. Only use this when the existing Z-Wave controller is missing or inoperable.\n• The Siren is now ready to be added to a new Z-Wave controller",
|
||
"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2039/YSL_External_Siren_SR-BX-ZW_1C.pdf"
|
||
}
|
||
}
|