72 lines
2.5 KiB
JSON
72 lines
2.5 KiB
JSON
{
|
||
"manufacturer": "HomeSeer Technologies",
|
||
"manufacturerId": "0x000c",
|
||
"label": "HS-MS100+",
|
||
"description": "Z-Wave Plus Motion Sensor",
|
||
"devices": [
|
||
{
|
||
"productType": "0x0201",
|
||
"productId": "0x0009",
|
||
"zwaveAllianceId": 2729
|
||
}
|
||
],
|
||
"firmwareVersion": {
|
||
"min": "0.0",
|
||
"max": "255.255"
|
||
},
|
||
"paramInformation": [
|
||
{
|
||
"#": "12",
|
||
"label": "Motion Sensor Sensitivity",
|
||
"description": "Higher values increase sensitivity",
|
||
"valueSize": 1,
|
||
"minValue": 0,
|
||
"maxValue": 8,
|
||
"defaultValue": 8,
|
||
"options": [
|
||
{
|
||
"label": "Disable",
|
||
"value": 0
|
||
}
|
||
]
|
||
},
|
||
{
|
||
"#": "14",
|
||
"$import": "templates/homeseer_template.json#enable_basic_set_command"
|
||
},
|
||
{
|
||
"#": "15",
|
||
"$import": "templates/homeseer_template.json#basic_set_value"
|
||
},
|
||
{
|
||
"#": "17",
|
||
"$import": "templates/homeseer_template.json#enable_shock_alarm"
|
||
},
|
||
{
|
||
"#": "18",
|
||
"label": "Motion Detection Timeout",
|
||
"valueSize": 2,
|
||
"unit": "seconds",
|
||
"minValue": 0,
|
||
"maxValue": 65525,
|
||
"defaultValue": 600,
|
||
"unsigned": true
|
||
},
|
||
{
|
||
"#": "19",
|
||
"$import": "~/templates/master_template.json#base_enable_disable",
|
||
"label": "Enable / Disable Binary Sensor for Motion",
|
||
"defaultValue": 1
|
||
},
|
||
{
|
||
"#": "32",
|
||
"$import": "templates/homeseer_template.json#low_battery_level"
|
||
}
|
||
],
|
||
"metadata": {
|
||
"inclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller in add mode (see the controller’s manual).\n4) Click the Z-button once, the LED indicator should blink fast. \n5) Wait for the adding process to end.\n6) Successful adding will be confirmed by the Z-Wave controller’s message.",
|
||
"exclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller remove mode (see the controller’s manual).\n4) Triple click the Z-button quickly, the LED indicator should blink fast.\n5) Wait for the removing process to end.\n6) Successful adding will be confirmed by the Z-Wave controller’s message.",
|
||
"reset": "1)Power on the device,\n2) Press and hold the Z button for more than 20 seconds,\n3) If holding time more than 20seconds, the LED indicator will keep on for 2 seconds, which means resetting is complete.\n4) The reset feature works only when the device has been included into a Z-Wave network.\n\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
|
||
"manual": "https://docs.homeseer.com/products/hs-ms100-user-guide"
|
||
}
|
||
}
|