{
	"manufacturer": "Aeotec Ltd.",
	"manufacturerId": "0x0371",
	"label": "ZWA018",
	"description": "Water Sensor 7 Basic",
	"devices": [
		{
			"productType": "0x0002",
			"productId": "0x0012"
		},
		{
			"productType": "0x0102",
			"productId": "0x0012"
		}
	],
	"firmwareVersion": {
		"min": "0.0",
		"max": "255.255"
	},
	"associations": {
		"1": {
			"label": "Lifeline",
			"maxNodes": 5,
			"isLifeline": true
		},
		"2": {
			"label": "Water Leakage (Control)",
			"maxNodes": 5
		},
		"3": {
			"label": "Water Leakage (Alarm)",
			"maxNodes": 5
		},
		"4": {
			"label": "Tamper (Alarm)",
			"maxNodes": 5
		}
	},
	"paramInformation": [
		{
			"#": "3[0x04]",
			"$import": "~/0x0086/templates/aeotec_template.json#led_indicator_wake"
		},
		{
			"#": "3[0x10]",
			"$import": "~/0x0086/templates/aeotec_template.json#led_indicator_tamper"
		},
		{
			"#": "4",
			"$import": "~/0x0086/templates/aeotec_template.json#range_test_double_click"
		},
		{
			"#": "5",
			"$import": "~/0x0086/templates/aeotec_template.json#association_group_2_trigger"
		},
		{
			"#": "6",
			"$import": "~/0x0086/templates/aeotec_template.json#association_group_2_command_type"
		},
		{
			"#": "7",
			"$import": "~/0x0086/templates/aeotec_template.json#association_group_2_basic_set_on"
		},
		{
			"#": "8",
			"$import": "~/0x0086/templates/aeotec_template.json#association_group_2_basic_set_off"
		},
		{
			"#": "9",
			"$import": "~/0x0086/templates/aeotec_template.json#time_delay_on"
		},
		{
			"#": "10",
			"$import": "~/0x0086/templates/aeotec_template.json#time_delay_off"
		},
		{
			"#": "11",
			"$import": "~/0x0086/templates/aeotec_template.json#time_delay_tamper"
		},
		{
			"#": "12",
			"$import": "~/0x0086/templates/aeotec_template.json#report_on_tamper_cancel"
		},
		{
			"#": "255",
			"$import": "~/0x0086/templates/aeotec_template.json#factory_reset_exclude"
		}
	],
	"metadata": {
		"inclusion": "1. Open the housing.\n2. Remove the battery protection.\n3. Press the tamper on the side of the appliance three times quickly",
		"exclusion": "1. Open the housing.\n2. Press the tamper on the side of the appliance three times quickly",
		"reset": "This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.\nOnce Cover is removed and the tamper switch is tripped, push the tamper for 5 seconds until the RED LED blinks once. Then release tamper and push it again for 5 seconds while the RED LED is blinking until the GREEN LED blinks once"
	}
}