{
	"manufacturer": "Vision Security",
	"manufacturerId": "0x0109",
	"label": "ZP3111-5",
	"description": "4-in-1 Sensor",
	"devices": [
		{
			"productType": "0x2021",
			"productId": "0x2101",
			"zwaveAllianceId": [1572, 1744, 2479]
		}
	],
	"firmwareVersion": {
		"min": "0.0",
		"max": "255.255"
	},
	"paramInformation": [
		{
			"#": "1",
			"label": "Temperature Scale",
			"valueSize": 1,
			"defaultValue": 0,
			"allowManualEntry": false,
			"options": [
				{
					"label": "Celsius",
					"value": 0
				},
				{
					"label": "Fahrenheit",
					"value": 1
				}
			]
		},
		{
			"#": "2",
			"label": "Temperature Offset",
			"valueSize": 1,
			"minValue": 0,
			"maxValue": 50,
			"defaultValue": 1
		},
		{
			"#": "3",
			"label": "Humidity",
			"description": "Configure Relative Humidity",
			"valueSize": 1,
			"unit": "%",
			"minValue": 1,
			"maxValue": 50,
			"defaultValue": 10
		},
		{
			"#": "4",
			"label": "Light Sensor",
			"valueSize": 1,
			"unit": "%",
			"minValue": 1,
			"maxValue": 50,
			"defaultValue": 10
		},
		{
			"#": "5",
			"label": "Trigger Interval",
			"description": "Set the trigger interval for motion sensor re-activation.",
			"valueSize": 1,
			"unit": "minutes",
			"minValue": 1,
			"maxValue": 255,
			"defaultValue": 3,
			"unsigned": true
		},
		{
			"#": "6",
			"label": "Motion Sensor Sensitivity",
			"description": "Adjust sensitivity of the motion sensor.",
			"valueSize": 1,
			"defaultValue": 4,
			"allowManualEntry": false,
			"options": [
				{
					"label": "Highest",
					"value": 1
				},
				{
					"label": "Higher",
					"value": 2
				},
				{
					"label": "High",
					"value": 3
				},
				{
					"label": "Normal",
					"value": 4
				},
				{
					"label": "Low",
					"value": 5
				},
				{
					"label": "Lower",
					"value": 6
				},
				{
					"label": "Lowest",
					"value": 7
				}
			]
		},
		{
			"#": "7",
			"label": "LED Indicator Mode",
			"valueSize": 1,
			"defaultValue": 3,
			"allowManualEntry": false,
			"options": [
				{
					"label": "Off",
					"value": 1
				},
				{
					"label": "Pulsing temperature, flashing motion",
					"value": 2
				},
				{
					"label": "Flashing temperature and motion",
					"value": 3
				}
			]
		}
	],
	"metadata": {
		"inclusion": "To add the ZP3111 to the Z-Wave network (inclusion), place the Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3111 for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3111 will go to sleep after 20 seconds.",
		"exclusion": "To remove the ZP3111 from the Z-Wave network (exclusion), place the Z-Wave primary controller into “exclusion” mode, and following its instruction to delete the ZP3111 to the controller. Press the Program Switch of ZP3111 once to be excluded.",
		"reset": "Remove cover to trigger tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3111 will send the “Device Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)",
		"wakeup": "Press the Programm Switch once.",
		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2479/ZP3111-5_R2_20170316.pdf"
	}
}