{
	"manufacturer": "SE Devices",
	"manufacturerId": "0x024f",
	"label": "AM",
	"description": "Standalone MOSFET Dimmer",
	"devices": [
		{
			"productType": "0x0003",
			"productId": "0x1012",
			"zwaveAllianceId": 2856
		}
	],
	"firmwareVersion": {
		"min": "0.0",
		"max": "255.255"
	},
	"paramInformation": [
		{
			"#": "1",
			"label": "Hardware Combination Identifier",
			"valueSize": 1,
			"defaultValue": 18,
			"readOnly": true,
			"allowManualEntry": false,
			"options": [
				{
					"label": "2-Pole 8A relay",
					"value": 16
				},
				{
					"label": "1-10V dimmer",
					"value": 17
				},
				{
					"label": "230V MOSFET dimmer",
					"value": 18
				},
				{
					"label": "1-Pole 16A relay",
					"value": 19
				}
			]
		},
		{
			"#": "10",
			"label": "Dimming Speed",
			"valueSize": 2,
			"unit": "0.01 seconds",
			"minValue": 0,
			"maxValue": 32767,
			"defaultValue": 300
		},
		{
			"#": "11",
			"label": "Dimmer Mode",
			"valueSize": 1,
			"defaultValue": 0,
			"allowManualEntry": false,
			"options": [
				{
					"label": "Leading edge",
					"value": 0
				},
				{
					"label": "Tailing edge",
					"value": 1
				}
			]
		},
		{
			"#": "12",
			"label": "Maximum Dimmer Level",
			"valueSize": 1,
			"minValue": 1,
			"maxValue": 99,
			"defaultValue": 90
		},
		{
			"#": "13",
			"label": "Minimum Dimmer Level",
			"valueSize": 1,
			"minValue": 1,
			"maxValue": 99,
			"defaultValue": 15
		},
		{
			"#": "16",
			"label": "Back Unit Type",
			"valueSize": 1,
			"defaultValue": 2,
			"readOnly": true,
			"allowManualEntry": false,
			"options": [
				{
					"label": "2-Pole 8A relay",
					"value": 0
				},
				{
					"label": "230V MOSFET dimmer",
					"value": 2
				},
				{
					"label": "1-10V dimmer",
					"value": 4
				},
				{
					"label": "1-Pole 16A relay",
					"value": 6
				}
			]
		},
		{
			"#": "44",
			"label": "Cold Start Minimum Level",
			"valueSize": 1,
			"minValue": 1,
			"maxValue": 99,
			"defaultValue": 20
		}
	],
	"metadata": {
		"inclusion": "To add the device to a Z-Wave network, the Z-Wave Controller must first be set into Add (Learn) mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
		"exclusion": "To remove the device from a Z-Wave network, the Z-Wave Controller must first be set into Remove mode. Then use a paperclip or a small pointy tool to push and hold the button in the button hole for approximately a second. The device LED will blink twice to indicate that it sends information to the Controller",
		"reset": "WARNING! Executing a Factory Reset on a device may make it stop working as wanted, and will disable remote control of the device. The device will have to be re-added to the Z-Wave network and reconfigured afterwards, to regain the previous operation of the device. Please DO NOT execute this procedure unless it is absolutely necessary.\n\nPush and Hold the Add/Remove button for about 15 seconds – until the LED indicator turns OFF. Then release the button. The device is now Factory Reset, and removed from the Z-Wave network.\n\nThe button is located about 10 mm down in the middle of the three holes on the front. A thin tool (a very small screwdriver, a toothpick, a paper clip or similar) is needed to access the button",
		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/2856/AMD_AD1-10V%20-%20Standalone%20Z-Wave%20Dimmer%20-%20User%20Manual.pdf"
	}
}