{
	"manufacturer": "HANK Electronics Ltd.",
	"manufacturerId": "0x0208",
	"label": "HKZW-SO01",
	"description": "Smart Plug with Two USB Ports",
	"devices": [
		{
			"productType": "0x0101",
			"productId": "0x0005"
		}
	],
	"firmwareVersion": {
		"min": "0.0",
		"max": "255.255"
	},
	"paramInformation": [
		{
			"#": "20",
			"label": "Overload Protection",
			"description": "If current exceeds 16.5A over 5 seconds, relay will turn off.",
			"valueSize": 1,
			"minValue": 0,
			"maxValue": 1,
			"defaultValue": 1
		},
		{
			"#": "21",
			"$import": "~/templates/master_template.json#state_after_power_failure_prev_on_off"
		},
		{
			"#": "24",
			"label": "Notification on Load Change",
			"description": "Smart Plug can send notifications to association device load state changes.",
			"valueSize": 1,
			"minValue": 0,
			"maxValue": 2,
			"defaultValue": 1
		},
		{
			"#": "27",
			"label": "Indicator Modes",
			"description": "LED in the device will indicate the state of load",
			"valueSize": 1,
			"minValue": 0,
			"maxValue": 1,
			"defaultValue": 0
		},
		{
			"#": "151",
			"label": "Threshold of Power Report",
			"description": "Power Threshold at which to send meter report",
			"valueSize": 2,
			"unit": "W",
			"minValue": 0,
			"maxValue": 65535,
			"defaultValue": 50,
			"unsigned": true
		},
		{
			"#": "152",
			"label": "Percentage Threshold of to Trigger Power Report",
			"valueSize": 1,
			"unit": "%",
			"minValue": 0,
			"maxValue": 255,
			"defaultValue": 10,
			"unsigned": true
		},
		{
			"#": "171",
			"label": "Power Report Frequency",
			"description": "The interval of sending power report to association device (Group Lifeline).",
			"valueSize": 4,
			"unit": "seconds",
			"minValue": 5,
			"maxValue": 2678400,
			"defaultValue": 30
		},
		{
			"#": "172",
			"label": "Energy Report Frequency",
			"description": "The interval of sending energy report to association device (Group Lifeline).",
			"valueSize": 4,
			"unit": "seconds",
			"minValue": 5,
			"maxValue": 2678400,
			"defaultValue": 300
		},
		{
			"#": "173",
			"label": "Voltage Report Frequency",
			"description": "The interval of sending voltage report to association device (Group Lifeline)",
			"valueSize": 4,
			"unit": "seconds",
			"minValue": 0,
			"maxValue": 2678400,
			"defaultValue": 0
		},
		{
			"#": "174",
			"label": "Electricity Report Frequency",
			"description": "Interval for sending electricity report.",
			"valueSize": 4,
			"unit": "seconds",
			"minValue": 0,
			"maxValue": 2678400,
			"defaultValue": 0
		}
	],
	"metadata": {
		"inclusion": "Automatic Non-Secure Inclusion\n1. Perform the steps in the INSTALLATION section above. If the plug-in has not already been included into a Z-Wave network, the LED indicator will blink rapidly. Otherwise, the plug-in has already been included and should first be excluded by following the instructions in the EXCLUSION section below.\n2. Set your Z-Wave controller into learning mode (refer to your controller's manual for instructions). The plug-in should be recognized and automatically included into your Z-Wave network.\n3. The auto-inclusion function will be disabled after the plug-in is included.\n\nManual Non-Secure Inclusion\n1. Perform the steps in the INSTALLATION section above. If the plug-in has not already been included into a Z-Wave network, the LED indicator will blink rapidly. Otherwise, the plug-in has already been included and should first be excluded by following the instructions in the EXCLUSION section below.\n2. Set your Z-Wave® controller into learning mode (refer to your controller's manual for instructions).\n3. Triple-click the Z-Button on the plug-in. The plug-in should be recognized and included into your Z-Wave network.\n\nManual Secure Inclusion\n1. Perform the steps in the INSTALLATION section above. If the plug-in has not already been included into a Z-Wave network, the LED indicator will blink rapidly. Otherwise, the plug-in has already been included and should first be excluded by following the instructions in the EXCLUSION section below.\n2. Set your Z-Wave controller into node secure mode (refer to your controller's manual for instructions).\n3. Press and hold the Z-Button for about 3 seconds. The LED indicator will begin blinking rapidly and the plug-in should be recognized and included into your Z- Wave network.",
		"exclusion": "1. Ensure that the plug-in is inserted into an AC outlet.\n2. Set your Z-Wave controller into learning mode (refer to your controller's manual for instructions).\n3. Triple-click the Z-Button. The plug-in will be removed from your Z-Wave network.",
		"reset": "Note that the plug-in can only be reset if it is included in a Z-Wave network.\n1. Ensure that the plug-in is inserted into an AC outlet.\n2. Press and hold the Z-Button on the plug-in for more than 20 seconds. The LED indicator will illuminate steadily for about 3 seconds, then will begin blinking slowly."
	}
}