{
	"manufacturer": "Everspring",
	"manufacturerId": "0x0060",
	"label": "AN188",
	"description": "Metering Plug",
	"devices": [
		{
			"productType": "0x0004",
			"productId": "0x000d",
			"zwaveAllianceId": 3139
		}
	],
	"firmwareVersion": {
		"min": "0.0",
		"max": "255.255"
	},
	"paramInformation": [
		{
			"#": "1",
			"label": "Basic Set Command Value",
			"description": "Allowable Range: 0-99",
			"valueSize": 2,
			"minValue": 0,
			"maxValue": 255,
			"defaultValue": 255,
			"options": [
				{
					"label": "On",
					"value": 255
				}
			]
		},
		{
			"#": "2",
			"label": "Group 1: Report Delay",
			"description": "Delaying time to report to group 1",
			"valueSize": 1,
			"unit": "seconds",
			"minValue": 3,
			"maxValue": 25,
			"defaultValue": 3
		},
		{
			"#": "3",
			"label": "Restore State After Power Loss",
			"valueSize": 1,
			"minValue": 0,
			"maxValue": 1,
			"defaultValue": 1,
			"options": [
				{
					"label": "Disable",
					"value": 0
				},
				{
					"label": "Enable",
					"value": 1
				}
			]
		},
		{
			"#": "4",
			"label": "Wattage Report Interval",
			"valueSize": 2,
			"unit": "minutes",
			"minValue": 0,
			"maxValue": 32767,
			"defaultValue": 1
		},
		{
			"#": "5",
			"label": "kWh Report Interval",
			"valueSize": 2,
			"unit": "minutes",
			"minValue": 0,
			"maxValue": 32767,
			"defaultValue": 60
		},
		{
			"#": "6",
			"label": "Wattage Report Threshold",
			"valueSize": 2,
			"unit": "W",
			"minValue": 0,
			"maxValue": 3500,
			"defaultValue": 0,
			"options": [
				{
					"label": "Disable",
					"value": 0
				}
			]
		},
		{
			"#": "7",
			"label": "Wattage Report Relative Change Threshold",
			"valueSize": 1,
			"minValue": 0,
			"maxValue": 100,
			"defaultValue": 0,
			"options": [
				{
					"label": "Disable",
					"value": 0
				}
			]
		}
	],
	"metadata": {
		"inclusion": "1. Put the Z-Wave Controller into inclusion mode.\n2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode.",
		"exclusion": "1. Put the Z-Wave Controller into exclusion mode.\n2. Press the link key three times within 1.5 seconds to put the unit into exclusion mode.",
		"reset": "1. Press the link key three times within 1.5 seconds to put the unit into exclusion mode.\n2. Within 1 second of step 1, press link key again and hold it until LED is off (about 5 seconds).\n3. Node ID is excluded. The device reverts to factory default state and will be in auto-inclusion mode for 25 secs.\n(Use this procedure only in the event that the network primary controller is missing, or otherwise inoperable.)",
		"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3139/AN188.pdf"
	}
}