{
	"manufacturer": "HomeSeer Technologies",
	"manufacturerId": "0x000c",
	"label": "HS-LS100+",
	"description": "Z-Wave Plus Leak Sensor",
	"devices": [
		{
			"productType": "0x0201",
			"productId": "0x000a",
			"zwaveAllianceId": 2735
		}
	],
	"firmwareVersion": {
		"min": "0.0",
		"max": "255.255"
	},
	"paramInformation": [
		{
			"#": "14",
			"$import": "templates/homeseer_template.json#enable_basic_set_command"
		},
		{
			"#": "15",
			"$import": "templates/homeseer_template.json#basic_set_value"
		},
		{
			"#": "17",
			"$import": "~/templates/master_template.json#base_0-255_nounit",
			"label": "Flood Alarm Interval",
			"unit": "minutes",
			"defaultValue": 5
		},
		{
			"#": "18",
			"$import": "templates/homeseer_template.json#enable_shock_alarm"
		},
		{
			"#": "19",
			"label": "Temperature Report Interval",
			"valueSize": 1,
			"unit": "1/10 minutes",
			"minValue": 3,
			"maxValue": 240,
			"defaultValue": 144,
			"unsigned": true
		},
		{
			"#": "20",
			"label": "Temperature (High) Alarm Trigger Threshold",
			"valueSize": 2,
			"unit": "0.1 °F",
			"minValue": -670,
			"maxValue": 2570,
			"defaultValue": 1040
		},
		{
			"#": "22",
			"label": "Temperature (Low) Trigger Threshold",
			"valueSize": 2,
			"unit": "0.1 °F",
			"minValue": -670,
			"maxValue": 2570,
			"defaultValue": 320
		},
		{
			"#": "24",
			"$import": "~/templates/master_template.json#base_enable_disable",
			"label": "Enable / Disable Blinking LED",
			"defaultValue": 1
		},
		{
			"#": "32",
			"$import": "templates/homeseer_template.json#low_battery_level"
		}
	],
	"metadata": {
		"inclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller in add mode (see the controller’s manual).\n4) Click the Z-button once (non-secure inclusion) or triple click (secure inclusion) the Z-button quickly, the LED indicator should blink fast. \n5) Wait for the adding process to end.\n6) Successful adding will be confirmed by the Z-Wave controller’s message.",
		"exclusion": "1) Open the cover.\n2) Place the device within the direct range of your Z-Wave controller.\n3) Set the main controller remove mode (see the controller’s manual).\n4) Triple click the Z-button quickly, the LED indicator should blink fast.\n5) Wait for the removing process to end.\n6) Successful adding will be confirmed by the Z-Wave controller’s message.",
		"reset": "1) Power on the device\n2) Press and hold the Z button for more than 20 seconds,\n3) If holding time more than 20seconds, the LED indicator will keep on for 2 seconds, which means resetting is complete.\n4) The reset feature works only when the device has been included into a Z-Wave network.\n\nUse this procedure only in the event that the network primary controller is missing or otherwise inoperable.",
		"manual": "https://docs.homeseer.com/products/hs-ls100-user-guide"
	}
}