zwave-js/.config-db/devices/0x0287/iblindsv3.json

{
	"manufacturer": "HAB Home Intelligence LLC",
	"manufacturerId": "0x0287",
	"label": "iblinds V3",
	"description": "Window Blind Controller",
	"devices": [
		{
			"productType": "0x0004",
			"productId": "0x0071"
		},
		{
			// New device ID, starting with v3.10
			"productType": "0x0004",
			"productId": "0x0072"
		}
	],
	"firmwareVersion": {
		"min": "0.0",
		"max": "255.255"
	},
	"associations": {
		"1": {
			"label": "Lifeline",
			"maxNodes": 1,
			"isLifeline": true
		}
	},
	"paramInformation": [
		{
			"#": "1",
			"label": "Close Interval",
			"description": "Auto Calibration Tightness. Lower value = tighter, Higher value = looser (MUST BE RECALIBRATED).",
			"valueSize": 1,
			"minValue": 16,
			"maxValue": 32,
			"defaultValue": 22
		},
		{
			"#": "2",
			"label": "Reverse Direction",
			"valueSize": 1,
			"defaultValue": 0,
			"allowManualEntry": false,
			"options": [
				{
					"label": "No",
					"value": 0
				},
				{
					"label": "Yes",
					"value": 1
				}
			]
		},
		{
			"#": "3",
			"label": "Send Reports",
			"description": "Used to disable Z-Wave Reports. This is useful for systems that poll iblinds immediately after sending a position command. Disable this if an immediate report is causing iblinds motor to function improperly.",
			"valueSize": 1,
			"defaultValue": 0,
			"allowManualEntry": false,
			"options": [
				{
					"label": "Enable",
					"value": 0
				},
				{
					"label": "Disable",
					"value": 1
				}
			]
		},
		{
			"#": "4",
			"label": "Default ON Value",
			"description": "Value that iblinds will open to by default",
			"valueSize": 1,
			"minValue": 0,
			"maxValue": 99,
			"defaultValue": 50
		},
		{
			"#": "5",
			"label": "Reset Button",
			"description": "Disabling the reset button on the motor prevents it from accidentally being pressed",
			"valueSize": 1,
			"defaultValue": 0,
			"allowManualEntry": false,
			"options": [
				{
					"label": "Enable",
					"value": 0
				},
				{
					"label": "Disable",
					"value": 1
				}
			]
		},
		{
			"#": "6",
			"label": "Movement Duration",
			"valueSize": 1,
			"unit": "seconds",
			"minValue": 0,
			"maxValue": 100,
			"defaultValue": 0
		},
		{
			"#": "7",
			"$if": "firmwareVersion >= 3.6",
			"label": "Remote Calibration",
			"valueSize": 1,
			"defaultValue": 0,
			"writeOnly": true,
			"allowManualEntry": false,
			"options": [
				{
					"label": "Idle",
					"value": 0
				},
				{
					"label": "Start calibration",
					"value": 1
				}
			]
		},
		{
			"#": "8",
			"$if": "firmwareVersion >= 3.7",
			"label": "Minimum Tilt Level",
			"valueSize": 1,
			"minValue": 0,
			"maxValue": 25,
			"defaultValue": 0,
			"writeOnly": true
		},
		{
			"#": "9",
			"$if": "firmwareVersion >= 3.7",
			"label": "Maximum Tilt Level",
			"valueSize": 1,
			"minValue": 75,
			"maxValue": 99,
			"defaultValue": 99,
			"writeOnly": true
		},
		{
			"#": "10",
			"$if": "firmwareVersion >= 3.7",
			"label": "Override Response to ON Command",
			"description": "Overrides Set commands with a value of 99 to use the value defined in parameter 4 (Default ON Value) instead",
			"valueSize": 1,
			"defaultValue": 0,
			"writeOnly": true,
			"allowManualEntry": false,
			"options": [
				{
					"label": "Disable",
					"value": 0
				},
				{
					"label": "Enable",
					"value": 1
				}
			]
		}
	],
	"compat": {
		// https://github.com/zwave-js/node-zwave-js/issues/5686
		// The device supports Binary Switch CC to control the tilt, but it is not linked
		// to the Window Covering CC values. Remove the Binary Switch CC to avoid confusion.
		"commandClasses": {
			"remove": {
				"Binary Switch": {
					"endpoints": "*"
				}
			}
		}
	}
}