116 lines
2.7 KiB
JSON
116 lines
2.7 KiB
JSON
|
{
|
||
|
|
"manufacturer": "Everspring",
|
||
|
|
"manufacturerId": "0x0060",
|
||
|
|
"label": "AN184",
|
||
|
|
"description": "Mini Plug with Metering",
|
||
|
|
"devices": [
|
||
|
|
{
|
||
|
|
"productType": "0x0004",
|
||
|
|
"productId": "0x000b",
|
||
|
|
"zwaveAllianceId": 3126
|
||
|
|
}
|
||
|
|
],
|
||
|
|
"firmwareVersion": {
|
||
|
|
"min": "0.0",
|
||
|
|
"max": "255.255"
|
||
|
|
},
|
||
|
|
"paramInformation": [
|
||
|
|
{
|
||
|
|
"#": "1",
|
||
|
|
"label": "Basic Set Command Value",
|
||
|
|
"description": "Allowable Range: 0-99",
|
||
|
|
"valueSize": 2,
|
||
|
|
"minValue": 0,
|
||
|
|
"maxValue": 255,
|
||
|
|
"defaultValue": 255,
|
||
|
|
"options": [
|
||
|
|
{
|
||
|
|
"label": "On",
|
||
|
|
"value": 255
|
||
|
|
}
|
||
|
|
]
|
||
|
|
},
|
||
|
|
{
|
||
|
|
"#": "2",
|
||
|
|
"label": "Group 1: Report Delay",
|
||
|
|
"description": "Delaying time to report to group 1",
|
||
|
|
"valueSize": 1,
|
||
|
|
"unit": "seconds",
|
||
|
|
"minValue": 3,
|
||
|
|
"maxValue": 25,
|
||
|
|
"defaultValue": 3
|
||
|
|
},
|
||
|
|
{
|
||
|
|
"#": "3",
|
||
|
|
"label": "Restore State After Power Loss",
|
||
|
|
"valueSize": 1,
|
||
|
|
"minValue": 0,
|
||
|
|
"maxValue": 1,
|
||
|
|
"defaultValue": 1,
|
||
|
|
"options": [
|
||
|
|
{
|
||
|
|
"label": "Disable",
|
||
|
|
"value": 0
|
||
|
|
},
|
||
|
|
{
|
||
|
|
"label": "Enable",
|
||
|
|
"value": 1
|
||
|
|
}
|
||
|
|
]
|
||
|
|
},
|
||
|
|
{
|
||
|
|
"#": "4",
|
||
|
|
"label": "Wattage Report Interval",
|
||
|
|
"valueSize": 2,
|
||
|
|
"unit": "minutes",
|
||
|
|
"minValue": 0,
|
||
|
|
"maxValue": 32767,
|
||
|
|
"defaultValue": 1
|
||
|
|
},
|
||
|
|
{
|
||
|
|
"#": "5",
|
||
|
|
"label": "kWh Report Interval",
|
||
|
|
"valueSize": 2,
|
||
|
|
"unit": "minutes",
|
||
|
|
"minValue": 0,
|
||
|
|
"maxValue": 32767,
|
||
|
|
"defaultValue": 60
|
||
|
|
},
|
||
|
|
{
|
||
|
|
"#": "6",
|
||
|
|
"label": "Wattage Report Threshold",
|
||
|
|
"valueSize": 2,
|
||
|
|
"unit": "W",
|
||
|
|
"minValue": 0,
|
||
|
|
"maxValue": 3500,
|
||
|
|
"defaultValue": 0,
|
||
|
|
"options": [
|
||
|
|
{
|
||
|
|
"label": "Disable",
|
||
|
|
"value": 0
|
||
|
|
}
|
||
|
|
]
|
||
|
|
},
|
||
|
|
{
|
||
|
|
"#": "7",
|
||
|
|
"label": "Wattage Report Relative Change Threshold",
|
||
|
|
"valueSize": 1,
|
||
|
|
"minValue": 0,
|
||
|
|
"maxValue": 100,
|
||
|
|
"defaultValue": 0,
|
||
|
|
"options": [
|
||
|
|
{
|
||
|
|
"label": "Disable",
|
||
|
|
"value": 0
|
||
|
|
}
|
||
|
|
]
|
||
|
|
}
|
||
|
|
],
|
||
|
|
"metadata": {
|
||
|
|
"inclusion": "1. Put the Z-Wave Controller into inclusion mode.\n2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode.",
|
||
|
|
"exclusion": "1. Put the Z-Wave Controller into exclusion mode.\n2. Press the link key three times within 1.5 seconds to put the unit into exclusion mode.",
|
||
|
|
"reset": "1. Press the link key three times within 1.5 seconds to put the unit into exclusion mode.\n2. Within 1 second of step 1, press link key again and hold it until LED is off (about 5 seconds).\n3. Node ID is excluded. The device reverts to factory default state and will be in auto-inclusion mode for 25 secs.\n(Use this procedure only in the event that the network primary controller is missing, or otherwise inoperable.)",
|
||
|
|
"manual": "https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3126/AN184%201022-A501112743R.pdf"
|
||
|
|
}
|
||
|
|
}
|